Panning, zooming, and rotating painfully slow while using SolidWorks Simulation

Has anyone else noted that panning, zooming, and rotating becomes painfully slow while setting up an analysis on an in SolidWorks Simulation? If I switch back to model view, everything is fine. It is only when I am in the simulation window/tab. I'm running an overclocked i7-4770k with a FirePro W5000.

Any suggestions?

SolidworksSimulation
Answers 22
SF
SF 2015-05-12 Best Answer

has always been like this?

version and service pack?

does this happen even on the simplest of parts?

it sounds like solidworks may not be using your graphics card and that in normal model mode your computer is fine

but when you're in simulation showing the results it isn't enough

could be using an onboard graphics card interfering or graphics card driver issue

SF
SF 2015-05-12

Hi Jared,

I'm using SolidWorks 2012 SP3.0. The problem is not present with simple parts. It does become apparent with even the simplest assemblies (a cylinder and block mated on flat faces). I have experienced this issue for as long as I can remember.

Matthew

SF
SF 2015-05-13

no files open

tools > options > systems options > use software opengl

what operating system are you using?

SF
SF 2015-05-13

I tried that option, and the same problem is there. I'm using Windows 7 Pro, 64 bit.

AT
AT 2015-05-13

Panning/zooming/rotating is almost always tied to your graphics card and driver, so that would be the direction I would take for troubleshooting.

What changed and when did it start happening?

SF
SF 2015-05-13

I have had this problem for a while. Knowing that these sorts of issues are usually graphics card and driver related, I did update to the latest driver provided on the AMD website last week.

SF
SF 2015-05-13

The AMD driver is 14.502.1019.

AT
AT 2015-05-13

Have you tried using the RX safe-modes to see if it's registry/option related?

SF
SF 2015-05-13

what system?

what happens if you disable the gfx at the os level?

SF
SF 2015-05-14

I disabled the W5000 in Device Manager so that the graphics are running off the on-chip Intel graphics. The problem is still there. Also, I have run through the diagnostic test on SolidWorks Rx: no problems found.

AT
AT 2015-05-14

Hi Matthew,

It doesn't sound graphical at this point. When you run the RX, try the safe-mode links on the home tab. Try to reproduce the issue in both of those safe-modes.

MP
MP 2015-05-14

Does this only happen when the mesh is shown?

SF
SF 2015-05-14

Nope. It happens with assemblies as soon as I'm working in an analysis tab. Mesh, or no mesh it happens. If I go back to the model tab, everything is fine.

SF
SF 2015-05-14

The issue is observed while using both safe modes.

JR
JR 2015-05-14

Stupid question: is your graphics card on the SW approved list?

How much RAM in the machine (32GB DDR3 or better?), video card RAM (2 to 8 GB DDR5 or better?)

SF
SF 2015-05-14

Yes, the AMD W5000 is on the approved list. I have 32 GB of DDR3. It has 2 GB of DDR5 RAM.

SF
SF 2015-05-14

post an example of a model with a study and results that you have trouble with

and maybe a video of what you are seeing

have you confirmed this isn't an issue on other computers?

SF
SF 2015-05-14

I'll see what I can do about providing some samples and/or a video. I just had my colleague try it on his Lenovo ThinkStation (i7-4770, Quadro k2000, SSD, 8GB RAM). He experienced the same issue that I have been experiencing.

SF
SF 2015-05-14

2 different systems

2 different gfx cards

supported gfx

supported operating systems

i'd say you have something on your system that is conflicting with solidworks, you could try msconfig'ing everything out and trying again

or what you're seeing is normal and you're just not used to it. but if this happens on a simple block with low mesh and not a lot of results visible, then something i go back to my above statement.

SF
SF 2015-05-15

I am have made some random, but simpler, models. The problem doesn't seem to be cropping up. Unfortunately, I can't share the exact files for confidentiality reasons. I suppose the models are more complicated that I thought. They do have some references (i.e. one part imported into another, plus assembly, plus lots of sketches, etc). I suppose that could be the issue...

SF
SF 2015-05-15

sounds good. that makes a lot more sense.

i'd recommend speaking with your var but if a k2000 can't handle it, you might just have a lot of data shown on the screen, hence the performance issue.

SF
SF 2015-05-15

The parts are sectioned to simplify the model, and to my eye, they aren't that complicated, and there are only three or four parts in the model. So I wonder if there is something deeper than the surface. I think for now, I will consider the question answered, and if I learn anything else I will awake the thread. Thanks everyone!