GENERAL TABLE IN DRAWING VIEW

Is it possible to place a General Table into a view? See attachment. I want to place the table between a couple blank dimensions. The problem is when I move the view, the table does not move. I'm assuming since the table is in the feature tree at the same level as the view, it cannot be done. I've also tried dragging the general table feature onto the view feature.
Sure, I can place the table in a corner and have notes for the dimensions saying to look for the table, but I prefer placing information where the dimensions are so a person does not have to look elsewhere on a drawing. I also place as many notes with the dimensions they belong with rather than making a person look elsewhere in a notes column. I find it easier and more efficient to read a drawing.

If no one has a solution, I will submit an enhancement request.

SolidworksDrawings And Detailing
Answers 16
KC
KC 2021-04-09 Best Answer

Hello,

Perhaps grouping the table and the view will remedy your OP.

Perhaps not.

Kevin

BH
BH 2021-04-09

I found an existing enhancement request, so I voted for it.

comment imagecomment image
KC
KC 2021-04-09

Super-Kludge:

Create a bunch of leaderless notes with Box border with linked contents, abutted and grouped together with the view.

Kevin

AL
AL 2021-04-09

I tried a few other things, thinking perhaps the programmer had not thought of covering that area, but they did.


What I tried was inserting an excel file over the view I wanted it linked to, hoping it would link itself, but it doesn't.

I also looked to see if you could convert tables to sketch but haven't found anything. If you could, then you could perhaps create the tables from the model itself and them import them in the drawing, convert them into sketches/blocks and then assign them to views. If a change were to be required, either delete the table and redo it entirely or modify it manually.

Perhaps a macro can do this..?

KC
KC 2021-04-09

Alex Lachance wrote:

I'm just spit balling here as I've never had the need to do something like this but how about creating a table inside the part or assembly instead of the drawing..? Perhaps you could then have it show up in the view you'd like..?

Hello,

I had tried that before my last replay.

I added a gen table to Front anno view but couldn't get the table to show in the view on the drawing.

Could be another case of operator failure though.

Kevin

AL
AL 2021-04-09

Dang... Then I believe it is not possible as of now as drawing tables are sheet dependant and not view dependant.

DP
DP 2021-04-09

Alex Lachance wrote:

Hey Dan,


The table might not show up because it might require to be ''shown manually''. Go in the feature tree on the desired view and see if you can have it be shown inside the view.

I tried that....but no table shows up in the feature tree at the drawing level.

AL
AL 2021-04-09

Hey Dan,


The table might not show up because it might require to be ''shown manually''. Go in the feature tree on the desired view and see if you can have it be shown inside the view.

DP
DP 2021-04-09

I just tried to do that.  And while the table shows up in the tree for my little assembly, when I add a view of that assembly to the drawing, the table is not shown in the tree for the view.

Also, inside the command "Insert Model Items", there doesn't seem to be a Table selection.   Inserting notes doesn't get the table either.

Good idea, but I can't figure it out.  

AL
AL 2021-04-09

I'm just spit balling here as I've never had the need to do something like this but how about creating a table inside the part or assembly instead of the drawing..? Perhaps you could then have it show up in the view you'd like..?

BH
BH 2021-04-09

There are no wasted answers when brainstorming.

KC
KC 2021-04-09

Dan Pihlaja wrote:

I don't believe that it is possible to add a table to a view.

 

The reason that I say this is that the anchors for these tables is inside the sheet format.  Which tells me that views and tables both must reside on the sheet.

‌,

The thought was to group a leadered note (with a space to remove its X box) with the table, but as you and Mr. Schroeder correctly stated, a table only belongs to the sheet and unless all entities for grouping are attached to the view, then no grouping.

To ‌, my apologies for the wasted effort on this suggestion.

Kevin

DP
DP 2021-04-09

I don't believe that it is possible to add a table to a view.

The reason that I say this is that the anchors for these tables is inside the sheet format.  Which tells me that views and tables both must reside on the sheet.

BH
BH 2021-04-09

I picked both. The 'Group' icon remains grayed out.

GS
GS 2021-04-09

Dan Pihlaja wrote:

Kevin Chandler wrote:

 

Hello,

 

Perhaps grouping the table and the view will remedy your OP.

 

Kevin

 

How do you do that?

I don't think you can if the table doesn't belong to the view.

DP
DP 2021-04-09

Kevin Chandler wrote:

Hello,

 

Perhaps grouping the table and the view will remedy your OP.

 

Kevin

How do you do that?