Drawing of assembly open. Possible to create additional sheets and detailing individual parts?

Hi all.

Very new to SW. Have a question related to drawings. So I model a couple of parts and make some assemblies with them. Then I make my final assembly with the sub-assemblies previously mentioned. Now I'm detailing the assembly but also need to detail the sub-assemblies and then the individual parts. Will I have to create a new drawing for each, or can I just create sheets in the main assembly and somehow right click a part in a view and "send to new sheet" or whatnot?

I know I can open the individual parts and assemblies and create a new sheet and then select the sub or part, but in this case the document properties I get in my Title Block pertain to the main assembly and not the sub or inserted part.

Maybe I'm making this overly complicated. Suggestions appreciated.

SolidworksDrawings And Detailing
Answers 13
CC
CC 2017-05-24 Best Answer

Yes, you can but I don't recommend to add more than one part/assembly to one dwg

If you really want to do this then

1) Add a new sheet (bottom left corner)

2)Click on model view and browser for new part or assembly

see below image

comment imagecomment image
MP
MP 2017-05-24

You are covering a few questions here.  What you are trying to do sounds possible.

First off, it sounds like you are going to want a "Parts Only" BOM based on your master assembly:

2017 SOLIDWORKS Help - Bill of Materials PropertyManager

This will list all of your parts in your BOM.  Though, you may want an "Indented" BOM, it is hard to be completely certain from your post.

It sounds as if you aren't dealing with a large assembly.  If that is the case a multi-sheet drawing file has several advantages over separate sheet per drawing files.

To add any views you want of any part or assembly to any sheet just browse for the part or assembly as circled below and insert the view into the drawing by dragging the views from the view pallet onto the sheet:

comment imagecomment image
MP
MP 2017-05-24

​,

I was in the middle of typing my post when you posted.  Just out of curiosity, why do you recommend not to add more than one part/asm per dwg file? 

CC
CC 2017-05-24

For better revision control

DG
DG 2017-05-24
<p>Nuno Marques wrote:</p><p></p><p>I know I can open the individual parts and assemblies and create a new sheet and then select the sub or part, but in this case the document properties I get in my Title Block pertain to the main assembly and not the sub or inserted part.</p>

Right click on the sheet and check/set this property

Also check the sheet format and make sure notes are properly linked to model and not drawing file.

comment imagecomment image
NN
NN 2017-05-25

Thanks for the reply. To be honest I hadn't even considered the revision issue. As I said, very new to SW and not even aware it's possible to do revision control. I'll have a look into it. Thanks!

NN
NN 2017-05-25

That first bit... swooosh! Right over my head. I think I get the gist of it, though. An indented BOM will show all parts in current assembly and the subs + all parts in the sub, right?

As for the adding sheets in the current drawing and adding parts to the new sheet, I knew I could do that, but as I said in my post, the title block would pull data from the current origin drawing / assembly and not from the part or sub in the current sheet. replied in the next comment that "custom properties"  for the sheet. I'm going to try that now.

NN
NN 2017-05-25

Thanks ​. I'll look into this today.

BH
BH 2017-05-25

For many years I created multi-sheet drawings beginning with the assembly, the assembly BOM, then individual parts, each sheet was named by the part number, and each sheet was had its rev driven from the part/asm file. On ordering, a PDF of the complete drawing was created and any other data for the supplier required at part level and put into a single folder. If a revision to a part was required this effects the BOM, so the upper asm was uprevved either major or minor depending on the change. A pdf of all sheets was created with the new rev level of the asm, the BOM would reflect the changed rev for the affected part(s) and any additional 3d/2d data was exported for the affected parts only, the obselete files were put into an archive folder. That way when ordering, we could order the asm-rev. All current files were in one place, and a complete history was readily accessible in the archive folder. Far easier in my opinion.

CC
CC 2017-05-25

Depend up to how you control the rev.  If the 2D dwg has rev. from the 3D model, then it'd be confused to have more than one 3D models per dwg

BH
BH 2017-05-25

It'd be confusing to have more than one 3D model per sheet yes, but that would be the case with any drawing, single sheet also. Where it gets confusing is the default rev table from SW writes the rev to the drawing file custom properties and can over-write the rev pulled in from the 3D's. So you need to ensure your revision data is pulled only from the relevant 3D's to the individual sheets.

CC
CC 2017-05-25
<span style="color: #333333; font-family: Verdana, 'Verdana Ref', Geneva, Tahoma, sans-serif; font-size: 14px;"> you need to ensure your revision data is pulled only from the relevant 3D's</span>

Yes, it's exactly what we do here .

CC
CC 2017-05-25

yes, Revision Control is not a simple issue as many thoughts - In the long term, if it's not managed properly, it'd cost lot of $$$ for the company

Imaging sending a wrong rev. to a company to produce million of parts