Manual

Can someone send me a copy of this manual

mtbguy2009@live.caSolidworksRouting
Comments 22
SD
SD 2009-04-16
send it to me too.

Please do this charity.

SF
SF 2009-04-16
Gentlemen, have you looked through the documentation on thiswebsite? Everything SW has is available online.
SO
SO 2009-04-16
I would be surprised if anyone has a PDF version of therouting manual. It is not readily available unless someone wentthrough the trouble of scanning it.
RJ
RJ 2009-04-16
I have a hard copy that I got from my VAR. I'd start thereand see if you can work out a deal with them.
SF
SF 2009-04-17
Or you can buy the Routing Manual and download it here in PDFform:
http://www.forefrontstudios.com/ffs-swrm/RMHome.htm

ML
ML 2009-04-17
Hmmm. Is that legal? If you can find someone selling abootleg, I'm sure you can find people who give it away.
SF
SF 2009-04-18
Wes Mosier has worked long and hard to create a Routingmanual that in my humble opinion is very needed. I certainly tookalot away from it. I also understand that Wes is currently busywith adding considerable Routing content to training DVDs. I lookforward to having that in place too.
For 50$ you are getting a great manual and a years worth of updatesto keep up with SW versions updates.
SF
SF 2009-04-20
Matt, the website says that it's a manual that hewrote.
SF
SF 2009-04-22
Hi all,

Yes, this manual is written 100% by Wes and I'd have to say I'dstrongly recommend it for piping users.

Cheers

Andy
SF
SF 2009-05-06
Is there a manual available for SW2009 for Vista? If so, doesanyone know where I can get it. I have a 2008 Solidworks Routingtraining manual from my VAR but none of the examples exist, orwork, with my Vista. The tutorial with 2009 is not verythorough.
SF
SF 2009-06-16
I am struggling with creating a routing assembly. We have ourfittings located on the network drive, but our design librarylocation is local. Therefore, I am not able to drag and drop tobegin a routing.

Any way around this?
SF
SF 2009-06-16
Don, you should probably move your question to a newpost.
SF
SF 2009-06-17
I note the comment from Andy above which begs the obviousquestion 'Why doesn't SolidWorks develop a better manual forpiping?'. Maybe Andy could comment.
SF
SF 2009-06-17

Don Lyons wrote:

 

I am struggling with creating a routing assembly. We have ourfittings located on the network drive, but our design librarylocation is local. Therefore, I am not able to drag and drop tobegin a routing.



Any way around this?

There are numerous ways around it. The route parts don't needto be in the design library at all. What you will need to avoid ishaving them both in the design library and on the networkedlocation. So, I would suggest that you:

1. Create your networked library, make sure it has everything init, both your own files and the standard routing files.
2. Move the routing folder out of the design library.
3. Add the networked folder into the design library dialog.
4. Set the routing library path to the new location intools,options,routing, Routing file locations. Any other paths toosuch as standard tubes file. You probably don't need to change theroute assembly template path.
5. Check that the correct paths are set in tools, options, filelocations.

Take care when doing this, if you get the paths wrong it may causeproblems.

#1 rule is make sure you don't have any files copied or availablethrough different paths. This can cause all sorts of problems.

Regards

Andy

SF
SF 2009-06-17

Derek Bishop wrote:

 

I note the comment from Andy above which begs the obviousquestion 'Why doesn't SolidWorks develop a better manual forpiping?'. Maybe Andy could comment.

Actually I think the manual we have isn't that bad. What weneed to do is make it available on every seat of SW premium. Notonly through a training course. Believe me, this is a battle I amfighting. I'm sure we will see things change soon.

In the meantime. I am writing a few documents myself. I have justposted one regarding piping with slope. I have a couple more I amworking on. I will post these others here in rough draft form.

Wes' manual is still the best bet at the moment I think.http://www.forefrontstudios.com/.

Wes worked incredibly hard on this and continues to improve on itall the time. There is also a basic routing course onSolidProfessor. More expensive but pretty good.

Regards

Andy
AK
AK 2009-06-22
Andy,
While you're at it perhaps you could help to move along aCircuitworks manual as well? I'm using Circuitworks to bring in 3dpopulated pcb's from my board layout guy, have it automaticallypopulate with accurate SW models of the connectors, and then routeusing the mating connectors and wires/cables. Learning this stuffis a real uphill battle, however, for packaging electronics intosmall spaces it's potentially an amazing tool.
Rather than a manual having videos with audio works the best forme. It would be great (and logical) if Circuitworks and electricalrouting were shown together. I've used the SolidProfessor videos,and while they're very good they're not as comprehensive as I'dlike.
Also, I realize that the whole point of this for SW is to makemoney, but having more savvy users will probably serve you betterthan the relatively small amount of money you might make sellingtraining materials.
Thanks,
Alan
SF
SF 2009-06-23
I think that the SW routing manual gives a fair indication oftheir commitment to developing the software and this addin.
SF
SF 2009-06-23

swrouting Solidworks wrote:

 

Actually I think the manual we have isn't that bad.

Andy

My view is that the abysmal standard of documentationavailable to purchasers of SW products is a good reason not toemploy anyone to operate it because their productivity would belousy on the sort of task that would justify the cost of purchasingSW.

I am not paying another subscription because it buys only buggyupdates, and at my present rate of learning the core product, itwill be years before I am ready to buy Simulation.

SW Corp's incompetence at technical writing is costing it money.

What I want is a comprehensive book that I can read from cover tocover, then dip into to read up on the topic that interests me atthe moment.

Don't mention the VAR. I would be happy to pay the people who helpme on this forum, but not my VAR.
DP
DP 2009-06-23
John,

I agree with you when you say that there is no really comprehensivemanual on SW Routing. The Routing (originally Piping) component asit was originally marketed was based upon flanged piping. You couldnot start a route without a flange. Obviously there are a lot ofpiping systems that don't use flanges.

Consequently, those of us who don't always have a route that startswith a "flange" had to develop our own library of piping parts,some of which were called flanges, just to establish a "startingpoint" of the piping assembly.

My point is not specific in referencing "flanges", but I hope toillustrate that Routing is more of a development platform for theuser than it is a comprehensive solution. And while SW provideslibraries of standard pipe fittings, you still need to develop yourown library of fittings, valves, filters, etc. to make the Routingproduct whole, where you can completely design a piping assembly.

From my experience the best manual is an online manual because theproduct is best described as a development platform. If this wereto be published in "book" form, the book would be obsolete withevery service pack, and you would have to buy the updated version.And while Wes Mosier has a manual that describes piping inconventional terms, I do not believe that it addresses electricalconduit, and especially any kind of flexible conduit. Or the wirethat you install inside the conduit.

But the Routing product should contain libraries of all standardpiping and wiring materials, as well as the instruction on how todevelop non-standard wires and pipes that incorporate physicalfeatures such as minimum bend radiuses.
SF
SF 2009-06-24
John,

You have always been able to start a route with items other thanflanges, in fact any routing item with only one C Point will do - Istart routes with bushes, unions, pipe caps, nipples, sockets, etc,etc. BTW, the library parts that ship with SW are very limited andwere probably only meant for people to use an an example so theycould make thier own. The lack of extensive library was my majorgripe when I originally purchase the piping add-in.

I only use the piping side of routing so I cannot comment on theelectrical stuff.

All new releases of SW used to be delivered with a great bookcalled the 'User Guide', but alas the last one was in 1999. Youwere able to read a chapter while having breakfast or on the bog,and 'shock horror' have it open on the desk beside you while youwere trying to get your head around a particular task - it was agreat help when I was creating my piping library.
SF
SF 2009-06-24

 

Don't mention the VAR. I would be happy to pay the people whohelp me on this forum, but not my VAR.

What do you need help with? <<$$$>>
SF
SF 2009-06-25
Ray,

I will get back to you when I feel that I have exhausted everyavenue I can think of to progress my task.